Exactly How to Install a Tub Yourself: Removing and Replacing.
Exactly How to Install a Tub Yourself: Removing and Replacing.
Blog Article
Do you find yourself trying to locate facts around A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is readily accessible, the task can relocate immediately; if you need to open a wall to get rid of the old bathtub and position the brand-new tub, the task is much harder. In either case, the task is within a house handyman's skills, although you will require an assistant to leave the old tub and also embeded in the new one. Make sure you have actually certified yourself for the job and also fit attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you might require a professional plumber to make tube links.
This short article will aid you set up a new tub in your restroom if you have actually already bought a brand-new tub and also don't require to alter the arrangement of your previous water pipes.
Your devices as well as material list ought to consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the restricted accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Protect the tap in place with the maker given backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type must be attached to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub as well as additionally examine the overflow outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait until the bath tub has actually been made use of a minimum of once as this will settle it right into its last setting.
Preparing for the Installation
To start with, the supporting structure provided with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, triggering the water to pass through the wall surface between the bathroom and the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the tiles making use of water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on Tools You Need to Install a New Bathtub , I imagined sharing that blog post was a good thing. Be sure to take the opportunity to distribute this post if you liked it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
Go Company Report this page